The International Journal of Engine Research publishes high quality papers on experimental and analytical studies that address a wide range of engine technologies.
The Journal is advised by an international Editorial Board of experts across a range of disciplines, headed by the Co-Editors-in-Chief.
Professor Hideyuki Ogawa, Hokkaido University, Japan
Professor Raul Payri, Universitat Politècnica de València, Spain
Professor Rolf Reitz, University of Wisconsin, Madison, USA
This journal is a member of the Committee on Publication Ethics (COPE).
For more information about the Journal please contact email@example.com
The International Journal of Engine Research publishes only the highest quality original and review papers on experimental and analytical studies of engine technology.
The journal is intended to serve as the premier source of long-term reference information about all aspects of engines and related technologies, including the latest research and developments affecting the automotive, railway, marine and aerospace industries as well as engines used for stationary power generation.
Original research papers are welcomed from all prospective authors. All manuscripts are rigorously reviewed by experienced and respected referees. Original research articles are expected to be thorough and complete, and to make a novel and significant contribution to the literature. Review articles are usually invited by the Editorial Board, although unsolicited review articles may be considered at the discretion of the Reviews Editor.
Research topics of interest include:
- In-cylinder flow
- Mixture distribution
- Ignition and combustion
- Exhaust emissions
- Combustion and emissions chemistry
- Combustion engine performance
- Fuel injection systems
- Fuel spray technology
- Fuels and lubricants
- Conventional and alternative fuels
- Piston-ring lubrication
- Gas exchange processes
- After-treatment technology
- Electronic engine controls
- 0D, 1D, 3D simulations of relevant thermophysical processes
- Powertrain simulation
- Optimatization of engines, powertrains and aftertreatment systems
- Rocket engines
- Gas turbine engines
- Engines and auxiliary power units for hybrid vehicles
- Stationary power generation
|H Ogawa||Hokkaido University, Japan|
|Raul Payri||Universitat Politècnica de València, Spain|
|Professor R Reitz||University of Wisconsin-Madison, USA|
|S Kokjohn||University of Wisconsin-Madison, USA|
|Y Mihara||Tokyo City University, Japan|
|Y Moriyashi||Chiba University, Japan|
|R Novella||Universitat Politècnica de València, Spain|
|Y Yamasaki||University of Tokyo, Japan|
|T Fansler||University of Wisconsin - Madison, USA|
|A K Agarwal||Indian Institute of Technology, Kanpur, India|
|C Bae||Korea Advanced Institute of Science and Technology, Korea|
|K Boulouchos||ETH Zürich, Switzerland|
|G Bruneaux||IFP Energies Nouvelles , France|
|M Canakci||Kocaeli University, Turkey|
|S Curran||Oak Ridge National Laboratory, USA|
|E Curtis||Ford Motor Company, USA|
|Manolis Gavaises||City University of London, England|
|M Günthner||University of Kaiserslautern, Germany|
|C Hasse||Technische Universität (TU) Darmstadt|
|Z Huang||Shanghai Jiao Tong University, China|
|T Ishiyama||Kyoto University, Japan|
|M Koike||Toyota Central R&D Labs., Inc., Japan|
|S-C Kong||Iowa State University, USA|
|J Kusaka||Waseda University, Japan|
|A Leipertz||Universität Erlangen-Nürnberg, Germany|
|P Miles||Sandia National Laboratories, USA|
|K Nakata||Toyota Motor Corporation, Japan|
|A Onorati||Politecnico di Milano, Italy|
|M Richter||Lund University, Sweden|
|M Trujillo||University of Wisconsin, USA|
|T Tsurushima||Nissan, Japan|
|N Uchida||New A.C.E Institute Co., Ltd, Japan|
|B M Vaglieco||Istituto Motori, Italy|
|H Zhao||Brunel University, UK|
|C Arcoumanis||City University, London, UK|
|D Assanis||University of Delaware, USA|
|I Denbratt||Chalmers University of Technolgy, Sweden|
|N Iida||Keio University, Japan|
|B Johansson||King Abdullah University, Saudi Arabia|
|T V Johnson||Corning Incorporated, USA|
|G Kalghatgi||Saudi Aramco, Saudi Arabia|
|T Ryan||Southwest Research Institute, USA|
|S Shuai||Tsinghua University, China|
|V Sick||The University of Michigan, USA|
|D Siebers||Sandia National Laboratories, USA|
|U Spicher||Karlstruhe Institute of Technology (KIT), Germany|
|W Su||Tianjin University, China|
|R M Wagner||Oak Ridge National Laboratory, USA|
Manuscript Submission Guidelines: International Journal of Engine Research
This Journal is a member of the Committee on Publication Ethics.
Please read the guidelines below then visit the Journal’s submission site http://mc.manuscriptcentral.com/ijer to upload your manuscript. Please note that manuscripts not conforming to these guidelines may be returned.
Only manuscripts of sufficient quality that meet the aims and scope of International Journal of Engine Research will be reviewed.
There are no fees payable to submit or publish in this journal.
As part of the submission process you will be required to warrant that you are submitting your original work, that you have the rights in the work, that you are submitting the work for first publication in the Journal and that it is not being considered for publication elsewhere and has not already been published elsewhere, and that you have obtained and can supply all necessary permissions for the reproduction of any copyright works not owned by you.
If you have any questions about publishing with SAGE, please visit the SAGE Journal Solutions Portal
- What do we publish?
1.1 Aims & Scope
1.2 Article types
1.3 Writing your paper
- Editorial policies
2.1 Peer review policy
2.5 Declaration of conflicting interests
2.6 Research Data
- Publishing policies
3.1 Publication ethics
3.2 Contributor's publishing agreement
3.3 Open access and author archiving
- Preparing your manuscript
4.2 Artwork, figures and other graphics
4.3 Supplementary material
4.4 Reference style
4.5 English language editing services
- Submitting your manuscript
5.2 Information required for completing your submission
- On acceptance and publication
6.1 SAGE Production
6.2 Online First publication
6.3 Access to your published article
6.4 Promoting your article
- Further information
Before submitting your manuscript to International Journal of Engine Research, please ensure you have read the Aims & Scope.
Original Article: Describes a piece of original or substantially original research, or some aspect of design development, manufacture, operation and maintenance, or engineering education
Review Article: A critical review of the state-of-the-art with examples of applications in design and profitable manufacture without extensive analysis
Case Study: Describes the application of a technique, procedure or management concept in a real situation
- In general, Original Articles, Review Papers and Case Studies should not normally exceed 5000 words (with up to 10 illustrations). Longer articles will be considered, however, as our criterion is that the content justifies the length of the article.
- Discussions on papers already published should not exceed 500 words and 2 illustrations.
The SAGE Author Gateway has some general advice and on how to get published, plus links to further resources.
1.3.1 Make your article discoverable
When writing up your paper, think about how you can make it discoverable. The title, keywords and abstract are key to ensuring readers find your article through search engines such as Google. For information and guidance on how best to title your article, write your abstract and select your keywords, have a look at this page on the Gateway: How to Help Readers Find Your Article Online.
Submissions to the journal are assessed by independent referees who make recommendations on the suitability of the articles for publication. We are committed to providing timely assessment of articles and authors are informed of the publication decision as soon as possible.
It should be noted that our refereeing process, common to many other publishers, is single-blind, that is, the referees remain anonymous and their identities are not released to authors. The referees, however, are informed of the authors’ names and affiliations.
As part of the submission process you will be asked to provide the names of 4 peers who could be called upon to review your manuscript. Recommended reviewers should be experts in their fields and should be able to provide an objective assessment of the manuscript. Please be aware of any conflicts of interest when recommending reviewers. Examples of conflicts of interest include (but are not limited to) the below:
- The reviewer should have no prior knowledge of your submission
- The reviewer should not have recently collaborated with any of the authors
- Reviewer nominees from the same institution as any of the authors are not permitted
Please note that the Editors are not obliged to invite any recommended/opposed reviewers to assess your manuscript.As part of the submission process you will be asked to provide the names of peers who could be called upon to review your manuscript. Recommended reviewers should be experts in their fields and should be able to provide an objective assessment of the manuscript. Please be aware of any conflicts of interest when recommending reviewers. Examples of conflicts of interest include (but are not limited to) the below:
The reviewer should have no prior knowledge of your submission
The reviewer should not have recently collaborated with any of the authors
Reviewer nominees from the same institution as any of the authors are not permitted
You will also be asked to nominate peers who you do not wish to review your manuscript (opposed reviewers).
Please note that the Editors are not obliged to invite/reject any recommended/opposed reviewers to assess your manuscript.
International Journal of Engine Research is committed to delivering high quality, fast peer-review for your paper, and as such has partnered with Publons. Publons is a third party service that seeks to track, verify and give credit for peer review. Reviewers for Journal of Engine Research can opt in to Publons in order to claim their reviews or have them automatically verified and added to their reviewer profile. Reviewers claiming credit for their review will be associated with the relevant journal, but the article name, reviewer’s decision and the content of their review is not published on the site. For more information visit the Publons website.
The Editor or members of the Editorial Board may occasionally submit their own manuscripts for possible publication in the journal. In these cases, the peer review process will be managed by alternative members of the Board and the submitting Editor/Board member will have no involvement in the decision-making process.
Papers should only be submitted for consideration once consent is given by all contributing authors. Those submitting papers should carefully check that all those whose work contributed to the paper are acknowledged as contributing authors.
The list of authors should include all those who can legitimately claim authorship. This is all those who:
- Made a substantial contribution to the concept or design of the work; or acquisition, analysis or interpretation of data,
- Drafted the article or revised it critically for important intellectual content,
- Approved the version to be published,
- Each author should have participated sufficiently in the work to take public responsibility for appropriate portions of the content.
Authors should meet the conditions of all of the points above. When a large, multicentre group has conducted the work, the group should identify the individuals who accept direct responsibility for the manuscript. These individuals should fully meet the criteria for authorship.
Acquisition of funding, collection of data, or general supervision of the research group alone does not constitute authorship, although all contributors who do not meet the criteria for authorship should be listed in the Acknowledgments section. Please refer to the International Committee of Medical Journal Editors (ICMJE) authorship guidelines for more information on authorship.
All contributors who do not meet the criteria for authorship should be listed in an Acknowledgements section. Examples of those who might be acknowledged include a person who provided purely technical help, or a department chair who provided only general support.
Any acknowledgements should appear first at the end of your article prior to your Declaration of Conflicting Interests (if applicable), any notes and your References.
2.3.1 Writing assistance
Individuals who provided writing assistance, e.g. from a specialist communications company, do not qualify as authors and so should be included in the Acknowledgements section. Authors must disclose any writing assistance – including the individual’s name, company and level of input – and identify the entity that paid for this assistance. It is not necessary to disclose use of language polishing services.
International Journal of Engine Research requires all authors to acknowledge their funding in a consistent fashion under a separate heading. Please visit the Funding Acknowledgements page on the SAGE Journal Author Gateway to confirm the format of the acknowledgment text in the event of funding, or state that: This research received no specific grant from any funding agency in the public, commercial, or not-for-profit sectors.
It is the policy of International Journal of Engine Research to require a declaration of conflicting interests from all authors enabling a statement to be carried within the paginated pages of all published articles.
Please ensure that a ‘Declaration of Conflicting Interests’ statement is included at the end of your manuscript, after any acknowledgements and prior to the references. If no conflict exists, please state that ‘The Author(s) declare(s) that there is no conflict of interest’. For guidance on conflict of interest statements, please see the ICMJE recommendations here.
At SAGE we are committed to facilitating openness, transparency and reproducibility of research. Where relevant, International Journal of Engine Research encourages authors to share their research data in a suitable public repository subject to ethical considerations and where data is included, to add a data accessibility statement in their manuscript file. Authors should also follow data citation principles. For more information please visit the Research Data Sharing Policies, which includes information about SAGE’s partnership with the data repository Figshare.
SAGE is committed to upholding the integrity of the academic record. We encourage authors to refer to the Committee on Publication Ethics’ International Standards for Authors and view the Publication Ethics page on the SAGE Author Gateway.
International Journal of Engine Research and SAGE take issues of copyright infringement, plagiarism or other breaches of best practice in publication very seriously. We seek to protect the rights of our authors and we always investigate claims of plagiarism or misuse of published articles. Equally, we seek to protect the reputation of the journal against malpractice. Submitted articles may be checked with duplication-checking software. Where an article, for example, is found to have plagiarised other work or included third-party copyright material without permission or with insufficient acknowledgement, or where the authorship of the article is contested, we reserve the right to take action including, but not limited to: publishing an erratum or corrigendum (correction); retracting the article; taking up the matter with the head of department or dean of the author's institution and/or relevant academic bodies or societies; or taking appropriate legal action.
3.1.2 Prior publication
If material has been previously published it is not generally acceptable for publication in a SAGE journal. However, there are certain circumstances where previously published material can be considered for publication. Please refer to the guidance on the SAGE Author Gateway or if in doubt, contact the Editor at the address given below.
Before publication, SAGE requires the author as the rights holder to sign a Journal Contributor’s Publishing Agreement. SAGE’s Journal Contributor’s Publishing Agreement is an exclusive licence agreement which means that the author retains copyright in the work but grants SAGE the sole and exclusive right and licence to publish for the full legal term of copyright. Exceptions may exist where an assignment of copyright is required or preferred by a proprietor other than SAGE. In this case copyright in the work will be assigned from the author to the society. For more information please visit the SAGE Author Gateway.
International Journal of Engine Research offers optional open access publishing via the SAGE Choice programme. For more information please visit the SAGE Choice website. For information on funding body compliance, and depositing your article in repositories, please visit SAGE Publishing Policies on our Journal Author Gateway.
The preferred format for your manuscript is Word. LaTeX files are also accepted. Word and (La)Tex templates are available on the Manuscript Submission Guidelines page of our Author Gateway.
For guidance on the preparation of illustrations, pictures and graphs in electronic format, please visit SAGE’s Manuscript Submission Guidelines.
Figures supplied in colour will appear in colour online regardless of whether or not these illustrations are reproduced in colour in the printed version. For specifically requested colour reproduction in print, you will receive information regarding the costs from SAGE after receipt of your accepted article.
This journal is able to host additional materials online (e.g. datasets, podcasts, videos, images etc) alongside the full-text of the article. For more information please refer to our guidelines on submitting supplementary files.
Authors seeking assistance with English language editing, translation, or figure and manuscript formatting to fit the journal’s specifications should consider using SAGE Language Services. Visit SAGE Language Services on our Journal Author Gateway for further information.
International Journal of Engine Research is hosted on SAGE Track, a web based online submission and peer review system powered by ScholarOne™ Manuscripts. Visit http://mc.manuscriptcentral.com/ijer to login and submit your article online.
IMPORTANT: Please check whether you already have an account in the system before trying to create a new one. If you have reviewed or authored for the journal in the past year it is likely that you will have had an account created. For further guidance on submitting your manuscript online please visit ScholarOne Online Help.
As part of our commitment to ensuring an ethical, transparent and fair peer review process SAGE is a supporting member of ORCID, the Open Researcher and Contributor ID. ORCID provides a unique and persistent digital identifier that distinguishes researchers from every other researcher, even those who share the same name, and, through integration in key research workflows such as manuscript and grant submission, supports automated linkages between researchers and their professional activities, ensuring that their work is recognized.
The collection of ORCID iDs from corresponding authors is now part of the submission process of this journal. If you already have an ORCID iD you will be asked to associate that to your submission during the online submission process. We also strongly encourage all co-authors to link their ORCID ID to their accounts in our online peer review platforms. It takes seconds to do: click the link when prompted, sign into your ORCID account and our systems are automatically updated. Your ORCID iD will become part of your accepted publication’s metadata, making your work attributable to you and only you. Your ORCID iD is published with your article so that fellow researchers reading your work can link to your ORCID profile and from there link to your other publications.
You will be asked to provide contact details and academic affiliations for all co-authors via the submission system and identify who is to be the corresponding author. These details must match what appears on your manuscript. At this stage please ensure you have included all the required statements and declarations and uploaded any additional supplementary files (including reporting guidelines where relevant).
Please also ensure that you have obtained any necessary permission from copyright holders for reproducing any illustrations, tables, figures or lengthy quotations previously published elsewhere. For further information including guidance on fair dealing for criticism and review, please see the Copyright and Permissions page on the SAGE Author Gateway.
Your SAGE Production Editor will keep you informed as to your article’s progress throughout the production process. Proofs will be sent by PDF to the corresponding author and should be returned promptly. Authors are reminded to check their proofs carefully to confirm that all author information, including names, affiliations, sequence and contact details are correct, and that Funding and Conflict of Interest statements, if any, are accurate. Please note that if there are any changes to the author list at this stage all authors will be required to complete and sign a form authorising the change.
Online First allows final articles (completed and approved articles awaiting assignment to a future issue) to be published online prior to their inclusion in a journal issue, which significantly reduces the lead time between submission and publication. Visit the SAGE Journals help page for more details, including how to cite Online First articles.
SAGE provides authors with online access to their final article.
Publication is not the end of the process! You can help disseminate your paper and ensure it is as widely read and cited as possible. The SAGE Author Gateway has numerous resources to help you promote your work. Visit the Promote Your Article page on the Gateway for tips and advice.
Any correspondence, queries or additional requests for information on the manuscript submission process should be sent to the International Journal of Engine Research editorial office as follows:
Assistant Managing Editor
SAGE Publications Ltd
1 Oliver's Yard, 55 City Road
London, EC1Y 1SP